Installation Guide – Stickers

• Soap solution or Window cleaner
• Alcohol 70%
• Clean microfiber cloths
• Squeegee
• Application Solution (100ml of Water mixed with 3-5 drops of Baby shampoo)
• Heat gun or hairdryer (optional)

1. Prepare the Surface:
   • Cleaning the surface: Use a soap solution or a window cleaner to clean the surface where the sticker will be applied. Remove any dirt and oils with Alcohol 70%.
   • Spray the Surface: Spray the application solution on the surface. This allows for easier repositioning.
2. Position the Sticker:
   • Spray the application solution: Spray the application solution on both sides of the Sticker. This prevents scratches during the application process.
   • Sticker Positioning: Carefully place the pre-cut sticker over the surface, ensuring it aligns properly. Adjust the positioning as necessary.
3. Apply the Sticker:
   • Use a Squeegee: Gently use a squeegee to push out water and air trapped under the sticker. Be careful to avoid scratching the sticker.
   • Use the Right Technique: Start from the center of the sticker and work your way outwards to push water and air bubbles out, rather than dragging the squeegee from one edge to another.
   • Handling Bubbles: If you encounter water bubbles or not a smooth area, lift the sticker back in that specific area, spray it again, and repeat the application process.
4. Final Touches:
   • Wipe Down: Use a soft cloth to gently wipe down the sticker, ensuring a smooth finish.
   • Inspect the Installation: Check for air bubbles or edges lifting. If necessary, use the squeegee or a needle to release trapped air.
5. Allow to Dry:
   • Drying Time: Allow the stickers to dry for at least 24-48 hours without exposing it to water or harsh conditions to ensure optimal adhesion.

• Work in a Clean Environment: Dust and debris can affect adhesion, so choose a clean workspace.
• Temperature Matters: Applying the stickers in a controlled environment around 15° C to 32°C (70°F to 90°F) is ideal for better adhesion.

MATERIALS NEEDED

• Soap solution or window cleaner
• Clean microfiber cloths
• Paper tape
• Squeegee
• Scissor

1. Clean the Surface
   • Thoroughly clean the area where the sticker will be applied using a soap solution or window cleaner. For optimal results, remove any dirt and oils with 70% alcohol.
2. Position the Sticker
   • Align the sticker according to your desired layout and secure it in place with paper tape.
3. Peel the Backing
   • Carefully cut and peel off half of the backing paper from the sticker.
4. Apply the Sticker
   • Using the squeegee, press the sticker onto the surface, starting from the center and working your way outward to eliminate air bubbles.
   • Once half of the sticker is applied, gradually remove the remaining backing paper while continuing to press the sticker down.
   • If your sticker comes with transfer paper, carefully remove it after the sticker is applied.
5. Smooth Out Air Bubbles
   • Use the squeegee to push out any remaining bubbles, directing air toward the edges. For stubborn bubbles, gently puncture them with a razor blade to release trapped air.
6. Allow to Set
   • Let the sticker adhere properly for at least 24 hours. During this time, avoid exposing it to water or harsh conditions.
7. Final Inspection
   • After the sticker has set, check for any areas needing further smoothing or adjustments.

• Temperature: Ideal application temperatures are between 60°F and 90°F (15°C to 32°C).
• Avoid Direct Sunlight: Install stickers in a shaded area to prevent the adhesive from drying too quickly.
• Patience is Key: Take your time to ensure proper alignment and a smooth application.

If you have any questions or need further assistance, feel free to reach out to our customer support team. Happy Styling!

1. Air Bubbles:
   Cause:
   • Air trapped underneath the sticker during application.
   Solution:
   • Use a squeegee or credit card to push bubbles toward the edges.
   • For stubborn bubbles, gently poke with a pin to release air and smooth it down.
   
2. Misalignment:
   Cause:
   • Sticker not positioned correctly before adhesion.
   Solution:
   • If the sticker is not yet fully adhered, gently peel it back and reposition it.
   • Use a soapy water solution for easier repositioning if it’s still in the initial stages.
   
3. Poor Adhesion:
   Cause:
   • Surface not cleaned properly or too much moisture.
   Solution:
   • Clean the surface with isopropyl alcohol to remove grease and dust.
   • Ensure the surface is completely dry before application.
   
4. Sticker Wrinkling:
   Cause:
   • Applying the sticker too quickly or without enough pressure.
   Solution:
   • If wrinkles occur, carefully peel back the sticker and reapply, smoothing it out as you go.
   • Use a squeegee to apply even pressure.
   
5. Sticker Not Sticking:
   Cause:
   • Surface is too cold or dirty.
   Solution:
   • Ensure the area is within the recommended temperature range 15°C to 32°C (60°F to 90°F).
   • Clean the surface thoroughly.
   
6. Damage to the Sticker:
   Cause:
   • Using excessive force or improper tools during application.
   Solution:
   • Handle stickers gently and use appropriate tools like a squeegee. If damaged, consider replacing the sticker.
   
7. Difficulty Removing Backing:
   Cause:
   • Sticker design may cause the backing to stick.
   Solution:
   • Gently roll the backing away from the sticker instead of pulling straight back.
   • Warm the sticker slightly with a hairdryer to loosen the adhesive if necessary.

• Practice Patience: Take your time during installation to avoid mistakes.
• Temperature Check: Ensure the application area is warm and dry for optimal adhesion.
• Seek Help: If needed, enlist a friend to assist with larger stickers for better alignment.

If problems persist, don’t hesitate to reach out to customer support for further assistance!